Dezembro 2022 vol. 10 num. 5 - 14º Congresso Brasileiro de Pesquisa e Desenvolvimento em Design

Artigo - Open Access.

Idioma principal | Segundo idioma

Desenvolvimento de máscara de proteção contra a COVID-19 utilizando manufatura aditiva

Paths and evolutions in the development of COVID-19 protective masking using additive manufacturing

YAMAKI, Roberto Takao ; CORREIA DE MELO, João Victor ; SANTOS, Jorge Roberto Lopes dos ; KAUFFMANN, Aline Reis ;

Artigo:

O presente trabalho apresenta parte da pesquisa da PUC-Rio dedicada à investigação de modelos de máscaras de proteção contra a COVID-19 de baixo custo, reaproveitáveis, facilmente fabricáveis e obedecendo às normas vigentes de filtragem. O objetivo deste trabalho consiste em apresentar o processo de design e a progressão de uma das alternativas de modelo para máscaras de proteção individual desenvolvidas pela equipe. Para isso foi desenvolvido um mapeamento que demonstra os avanços obtidos com os contínuos esforços para aprimoramento e desenvolvimento de novas soluções. O critério para esta seleção consistiu em abordar as versões desenvolvidas que contém desdobramentos e soluções técnicas essenciais à obtenção de um modelo de máscara de proteção individual que foi encaminhado aos órgãos responsáveis pela regulamentação de tais equipamentos.

Artigo:

This paper presents part of the research at PUC-Rio dedicated to the investigation of models of protective masks against COVID-19 that are low cost, reusable, easily manufactured, and comply with current filtering standards. The objective of this work is to present the design process and the progression of one of the model alternatives for individual protection masks developed by the team. To this end, a chart was developed that demonstrates the progress obtained with the continuous efforts for improvement and development of new solutions. The development procedures are aligned with the Research through Design (RtD) methodology. The criterion for the selection of the masks that are detailed in this work consisted in approaching the developed versions that contain unfoldings and technical solutions essential to obtain a model of individual protection mask that will be forwarded to the agencies responsible for the regulation of such equipment.

Download (PDF)

Palavras-chave: Máscara de Proteção; COVID-19; Máscara Cirúrgica.,

Palavras-chave: Protective Mask; COVID-19; Surgical Mask.,

DOI: 10.5151/ped2022-7791844

Referências bibliográficas
  • [1] ABD-ELSAYED, Alaa; KARRI, Jay. Utility of substandard face mask options for health care workers during the COVID-19 pandemic. Anesthesia and analgesia, 2020. DOI: 10.1213/ANE.0000000000004841
  • [2] CLAPP, Phillip W. et al. Evaluation of cloth masks and modified procedure masks as personal protective equipment for the public during the COVID-19 pandemic. JAMA Internal Medicine, v. 181, n. 4, p. 463-469, 2021. DOI:10.1001/jamainternmed.2020.8168
  • [3] CORTES, Arthur Rodriguez Gonzalez et al. Use of free CAD software for 3D printing individualized face masks based on face scans Einsatz von CAD-Freeware zur Individualisierung 3-D-gedruckter Atemschutzmasken anhand von Gesichtsscans. International journal of computerized dentistry, v. 23, n. 2, p. 183-189, 2020. PMID: 32337516
  • [4] DALSGAARD, Peter; HALSKOV, Kim. Reflective design documentation. In: Proceedings of the Designing Interactive Systems Conference. 2012. p. 428-437.
  • [5] GALZO, Weslley. Máscaras N95 falsificadas são vendidas ‘livremente’; saiba como identificar. CNN, São Paulo. 2021. Disponível em:
  • [6] https://www.cnnbrasil.com.br/saude/mascaras-n95-falsificadas-sao-vendidas-livremente-saiba-como-identificar. Acesso em: 17 mar 2022.
  • [7] GIERTHMUEHLEN, Mortimer et al. Evaluation and discussion of handmade face-masks and commercial diving-equipment as personal protection in pandemic scenarios. PLoS one, v. 15, n. 8, p. e0237899, 2020. Aug 19;15(8):e0237899. DOI: 10.1371/journal.pone.0237899. PMID: 32813727; PMCID: PMC7437915.
  • [8] ISHACK, Stephanie; LIPNER, Shari R. Applications of 3D printing technology to address COVID-19–related supply shortages. The American journal of medicine, v. 133, n. 7, p. 771, 2020. DOI: 10.1016/j.amjmed.2020.04.002
  • [9] ISO/TS 16976-2. Techincal Specification: Respiratory protective devices - Human factors. Part 2: Anthropometrics. Second Edition, 01/04/2015. ISO/TS 16976-2:2015(E)
  • [10] JOHNSON, D. F. et al. A quantitative assessment of the efficacy of surgical and N95 masks to filter influenza virus in patients with acute influenza infection. Clinical Infectious Diseases, v. 49, n. 2, p. 275-277, 2009. DOI: https://doi.org/1086/600041.
  • [11] KARUPPASAMY, Karunakaravel; OBUCHOWSKI, Nancy. Comparison of fit for sealed and loose-fitting surgical masks and N95 filtering facepiece respirators. Annals of work exposures and health, v. 65, n. 4, p. 463-474, 2021. DOI: 10.1093/annweh/wxaa125. PMID: 33458738; PMCID: PMC7929389.
  • [12] LEUNG, Nancy HL et al. Respiratory virus shedding in exhaled breath and efficacy of face masks. Nature medicine, v. 26, n. 5, p. 676-680, 2020. DOI: https://doi.org/10.1038/s41591-020-0843-2.
  • [13] MILTON, Donald K. et al. Influenza virus aerosols in human exhaled breath: particle size, culturability, and effect of surgical masks. PLoS pathogens, v. 9, n. 3, p. e1003205, 20 DOI: https://doi.org/10.1371/journal.ppat.1003205
  • [14] NOVAK, James I.; LOY, Jennifer. A critical review of initial 3D printed products responding to COVID-19 health and supply chain challenges. Emerald Open Research, v. 2, 2020. DOI: 10.35241/emeraldopenres.13697.1
  • [15] PAN, Xiangbin et al. Assessment of use and fit of face masks among individuals in public during the COVID-19 pandemic in China. JAMA network open, v. 4, n. 3, p. e212574-e212574, 2021. DOI: 10.1001/jamanetworkopen.2021.2574. PMID: 33704478; PMCID: PMC7953274.
  • [16] RUNDE, Daniel P. et al. The “double eights mask brace” improves the fit and protection of a basic surgical mask amidst COVID‐19 pandemic. Journal of the American College of Emergency Physicians Open, v. 2, n. 1, p. e12335, 2021. DOI: https://doi.org/10.1002/emp2.12335
  • [17] SANTOS, Jorge Roberto Lopes et al. Confronting COVID-19-The case of PPE and Medical Devices production using Digital Fabrication at PUC-Rio. Strategic Design Research Journal, v. 13, n. 3, p. 488-501, 2020. DOI: 10.4013/sdrj.2020.133.15.
  • [18] SILVA, Marivaldo Cavalcante. Descarte de máscaras nas imediações de equipamentos de saúde pública na pandemia do COVID-19 em Araguaína-TO. Holos, v. 5, p. 1-13, 2020. DOI: https://doi.org/10.15628/holos.2020.10136
  • [19] SUREKA, Binit; GARG, Mahendra Kumar; MISRA, Sanjeev. N95 respirator and surgical mask in the pandemic of COVID- Annals of Thoracic Medicine, v. 15, n. 4, p. 247, 2020.
  • [20] SWENNEN, Gwen RJ; POTTEL, Lies; HAERS, Piet E. Custom-made 3D-printed face masks in case of pandemic crisis situations with a lack of commercially available FFP2/3 masks. International Journal of Oral and Maxillofacial Surgery, v. 49, n. 5, p. 673-677, 20 DOI: https://doi.org/10.1016/j.ijom.2003.015
  • [21] WANG, M. W. et al. Mask crisis during the COVID-19 outbreak. Eur Rev Med Pharmacol Sci, v. 24, n. 6, p. 3397-3399, 2020. DOI: 10.26355/eurrev_202003_20707. PMID: 32271457.
  • [22] WORLD HEALTH ORGANIZATION et al. Advice on the use of masks in the context of COVID-19: interim guidance, 5 June 2020. World Health Organization, 2020a.
  • [23] WORLD HEALTH ORGANIZATION et al. Mask use in the context of COVID-19: interim guidance, 1 December 2020. World Health Organization, 2020b.
  • [24] ZIMMERMAN, John; FORLIZZI, Jodi; EVENSON, Shelley. Research through design as a method for interaction design research in HCI. In: Proceedings of the SIGCHI conference on Human factors in computing systems. 2007. p. 493-502. DOI: https://doi.org/10.1145/124061240704_x000C_
Como citar:

YAMAKI, Roberto Takao; CORREIA DE MELO, João Victor; SANTOS, Jorge Roberto Lopes dos; KAUFFMANN, Aline Reis; "Desenvolvimento de máscara de proteção contra a COVID-19 utilizando manufatura aditiva", p. 1866-1893 . In: Anais do 14º Congresso Brasileiro de Pesquisa e Desenvolvimento em Design. São Paulo: Blucher, 2022.
ISSN 2318-6968, DOI 10.5151/ped2022-7791844

últimos 30 dias | último ano | desde a publicação


downloads


visualizações


indexações